{"id":2441,"date":"2024-05-17T08:07:31","date_gmt":"2024-05-17T08:07:31","guid":{"rendered":"https:\/\/mdmetrology.com.sg\/th\/?p=2441"},"modified":"2024-05-24T03:17:20","modified_gmt":"2024-05-24T03:17:20","slug":"why-simple-acceptance-decision-rules-matter-in-todays-fast-paced-world","status":"publish","type":"post","link":"https:\/\/mdmetrology.com.sg\/th\/why-simple-acceptance-decision-rules-matter-in-todays-fast-paced-world\/","title":{"rendered":"How to Apply the Decision Rule in a Calibration Results."},"content":{"rendered":"\t\t
\n\t\t\t\t
\n\t\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t

Samples for Simple Acceptance Decision Rule\u200b<\/h2>\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

The following are sample data from the different areas of calibration.
The decision is based on the different rules to show a comparison.<\/p>

1. Dimensional<\/b><\/span><\/span><\/p>

Sample: Caliper<\/b><\/p>

Existing Decision Rule (following APLAC TC 004)<\/b><\/span><\/span><\/p>

Calibration Results<\/b><\/span><\/p>

Specification\/ Tolerance taken from JIS B 7507 : 2016.<\/b><\/p>

Instrument Error of External Measurement<\/span><\/p>

Nominal<\/p>

(mm)<\/p><\/td>

Permissible Error
(mm)<\/td>		Measured Value
(mm)<\/td>

Error<\/p>

(mm)<\/p><\/td>

Decision<\/td><\/tr>
0<\/td>\u00a0<\/td>0.00<\/td>0.00<\/td>Intolerance<\/td><\/tr>
20<\/td>\u00a0<\/td>20.02<\/td>+0.02<\/td>Intolerance<\/td><\/tr>
50<\/td>

\u00b1 0.03<\/p><\/td>

50.03<\/td>+0.03<\/td>Indeterminate<\/td><\/tr>
100<\/td>\u00a0<\/td>100.04<\/td>+0.04<\/td>Indeterminate<\/td><\/tr>
150<\/td>\u00a0<\/td>150.05**<\/td>+0.05<\/td>Out of tolerance<\/td><\/tr><\/tbody><\/table>

The expanded uncertainty is \u00b1 0.01 mm, at approximately 95% confidence level with coverage factor, k <\/i>= 2<\/p>
\u00a0<\/td>

This item fulfils the requirements given in the above stated standard.<\/del><\/p><\/td><\/tr>

\u00a0<\/td>

The requirements stated in this report are taken from the above stated standard.<\/del><\/p><\/td><\/tr>

Final Statement in report<\/p><\/td>

Measured value marked ** does not fulfil the requirements given in the above stated standard.<\/p><\/td><\/tr><\/tbody><\/table>

New: Simple Acceptance Rule (following ILAC G8)<\/b><\/p>

Calibration Results<\/b><\/span><\/p>

Specification\/ Tolerance taken from JIS B 7507 : 2016.<\/b><\/p>

Instrument Error of External Measurement<\/span><\/span><\/p>

Nominal<\/p>

(mm)<\/p><\/td>

Permissible Error
(mm)<\/td>		Measured Value
(mm)<\/td>

Error<\/p>

(mm)<\/p><\/td>

Decision<\/td><\/tr>
0<\/td>\u00a0<\/td>0.00<\/td>0.00<\/td>Intolerance<\/td><\/tr>
20<\/td>\u00a0<\/td>20.02<\/td>+0.02<\/td>Intolerance<\/td><\/tr>
50<\/td>

\u00b1 0.03<\/p><\/td>

50.03<\/td>+0.03<\/td>Indeterminate<\/td><\/tr>
100<\/td>\u00a0<\/td>100.04**<\/td>+0.04<\/td>Indeterminate<\/td><\/tr>
150<\/td>\u00a0<\/td>150.05**<\/td>+0.05<\/td>Out of tolerance<\/td><\/tr><\/tbody><\/table>

The expanded uncertainty is \u00b1 0.01 mm, at approximately 95% confidence level with coverage factor, k <\/i>= 2.<\/p>
\u00a0<\/td>

The measured values were observed in tolerance at the points calibrated.<\/del><\/p><\/td><\/tr>

Final Statement in report<\/p><\/td>

Measured value marked ** was observed out of tolerance at the points calibrated.<\/p><\/td><\/tr><\/tbody><\/table>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t

\n\t\t\t\t
\n\t\t\t\t\t\t\t
\n\t\t\t\n\t\t\t\t\t\t<\/span>\n\t\t<\/div>\n\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t
\n\t\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

Samples for Simple Acceptance Decision Rule<\/b><\/p>

The following are sample data from the different areas of calibration.<\/p>

The decision is based on the different rules to show a comparison.<\/p>

1. Dimensional<\/b><\/span><\/span><\/p>

Sample: Micrometer<\/b><\/p>

Existing Decision Rule (following APLAC TC 004)<\/b><\/span><\/span><\/p>

Calibration Results<\/b><\/span><\/p>

Specification\/ Tolerance taken from BS 870 : 2008.<\/b><\/p>

Feature Inspected<\/p><\/td>

Allowable Error
(inch)<\/p><\/td>

Measured Value
(inch)<\/p><\/td>

ExpandedUncertainty<\/p>

(inch)<\/p><\/td>

Decision<\/p><\/td><\/tr>

Flatness of Measuring Face<\/p><\/td>

0.00005<\/p><\/td>

0.00005<\/p><\/td>

\u00b1 0.0000<\/p><\/td>

Indeterminate<\/p><\/td><\/tr>

Parallelism of Measuring Face<\/p><\/td>

0.0001<\/p><\/td>

0.00008<\/p><\/td>

\u00b1 0.00004<\/p><\/td>

Indeterminate<\/p><\/td><\/tr>

Range of Error of Micrometer Screw<\/p><\/td>

0.0001<\/p><\/td>

0.00005<\/p><\/td>

\u00b1 0.00005<\/p><\/td>

Intolerance<\/p><\/td><\/tr><\/tbody><\/table>

The expanded uncertainty is at approximately 95% confidence level with coverage factor, k <\/i>= 2.<\/p>
\u00a0<\/td>

This item fulfils the requirements given in the above stated standard.<\/del><\/p><\/td><\/tr>

Final Statement in report<\/p><\/td>

The requirements stated in this report are taken from the above stated standard.<\/p><\/td><\/tr>

\u00a0<\/td>

Measured value marked ** does not fulfil the requirements given in the above stated standard.<\/p><\/td><\/tr><\/tbody><\/table>

New: Simple Acceptance Rule (following ILAC G8)<\/b><\/span><\/span><\/p>

Calibration Results<\/b><\/span><\/p>

Specification\/ Tolerance taken from BS 870 : 2008.<\/b><\/p>

Feature Inspected<\/p><\/td>

Allowable Error<\/p>

(inch)<\/p><\/td>

Measured Value<\/p>

(inch)<\/p><\/td>

ExpandedUncertainty<\/p>

(inch)<\/p><\/td>

Decision<\/p><\/td><\/tr>

Flatness of Measuring Face<\/p><\/td>

0.00005<\/p><\/td>

0.00005<\/p><\/td>

\u00b1 0.0000<\/p><\/td>

Intolerance<\/p><\/td><\/tr>

Parallelism of Measuring Face<\/p><\/td>

0.0001<\/p><\/td>

0.00008<\/p><\/td>

\u00b1 0.00004<\/p><\/td>

Intolerance<\/p><\/td><\/tr>

Range of Error of Micrometer Screw<\/p><\/td>

0.0001<\/p><\/td>

0.00005<\/p><\/td>

\u00b1 0.00005<\/p><\/td>

Intolerance<\/p><\/td><\/tr><\/tbody><\/table>

The expanded uncertainty is at approximately 95% confidence level with coverage factor, k <\/i>= 2.<\/p>

Final Statement in report<\/p><\/td>

The measured values were observed in tolerance at the points calibrated.<\/p><\/td><\/tr>

\u00a0<\/td>

Measured value marked ** was observed out of tolerance at the points calibrated.<\/del><\/p><\/td><\/tr><\/tbody><\/table>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t

\n\t\t\t\t
\n\t\t\t\t\t\t\t
\n\t\t\t\n\t\t\t\t\t\t<\/span>\n\t\t<\/div>\n\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t
\n\t\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

Samples for Simple Acceptance Decision Rule<\/b><\/p>

The following are sample data from the different areas of calibration.<\/p>

The decision is based on the different rules to show a comparison.<\/p>

2. Mechanical<\/b><\/span><\/span><\/p>

Sample: Pressure Gauge<\/b><\/p>

Existing Decision Rule (following APLAC TC 004)<\/b><\/span><\/span><\/p>

Calibration Results<\/b><\/span><\/p>

Specification \/ Tolerance taken from Manufacturer’s Specification : \u00b1 0.1 % of Full Scale.<\/b><\/p>

UUT Indicated Value<\/p><\/td>

Applied Pressure<\/p><\/td>

Decision<\/p><\/td><\/tr>

0<\/p><\/td>

Ascending<\/p><\/td>

Error<\/p><\/td>

\u00a0<\/td><\/tr>
0<\/td>

0.00<\/p><\/td>

0.00<\/p><\/td>

Intolerance<\/p><\/td><\/tr>

100<\/p><\/td>

100.02<\/p><\/td>

-0.02<\/p><\/td>

Intolerance<\/p><\/td><\/tr>

300<\/td>

300.16<\/p><\/td>

-0.16<\/p><\/td>

Indeterminate<\/p><\/td><\/tr>

400<\/td>

400.41<\/p><\/td>

-0.41<\/p><\/td>

Indeterminate<\/p><\/td><\/tr><\/tbody><\/table>

All units are in psi.<\/p>

The expanded uncertainty is \u00b1 0.06 % of Full Scale, at approximately 95% confidence level with coverage factor, k <\/i>= 2.<\/p>
\u00a0<\/td>

This item fulfils the requirements given in the above stated standard.<\/p><\/td><\/tr>

Final Statement in report<\/p><\/td>

The requirements stated in this report are taken from the above stated standard.<\/p><\/td><\/tr>

\u00a0<\/td>

Measured value marked ** does not fulfil the requirements given in the above stated standard.<\/p><\/td><\/tr><\/tbody><\/table>

New: Simple Acceptance Rule (following ILAC G8)<\/b><\/span><\/span><\/p>

Calibration Results<\/b><\/span><\/p>

Specification \/ Tolerance taken from Manufacturer’s Specification : \u00b1 0.1 % of Full Scale.<\/b><\/p>

UUT Indicated Value<\/p><\/td>

Applied
Pressure<\/p><\/td>

Decision<\/p><\/td><\/tr>

0<\/p><\/td>

Ascending<\/p><\/td>

Error<\/p><\/td>

\u00a0<\/td><\/tr>
0<\/td>

0.00<\/p><\/td>

0.00<\/p><\/td>

Intolerance<\/p><\/td><\/tr>

100<\/p><\/td>

100.02<\/p><\/td>

-0.02<\/p><\/td>

Intolerance<\/p><\/td><\/tr>

300<\/td>

300.16<\/p><\/td>

-0.16<\/p><\/td>

Intolerance<\/p><\/td><\/tr>

400<\/td>

400.41**<\/p><\/td>

-0.41<\/p><\/td>

Out of tolerance<\/p><\/td><\/tr><\/tbody><\/table>

All units are in psi.<\/p>

The expanded uncertainty is \u00b1 0.06 % of Full Scale, at approximately 95% confidence level with coverage factor, k <\/i>= 2.<\/p>

\u00a0<\/p>
\u00a0<\/td>

The measured values were observed in tolerance at the points calibrated.<\/p><\/td><\/tr>

Final Statement in report<\/p><\/td>

Measured value marked ** was observed out of tolerance at the points calibrated.<\/p><\/td><\/tr><\/tbody><\/table>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t

\n\t\t\t\t
\n\t\t\t\t\t\t\t
\n\t\t\t\n\t\t\t\t\t\t<\/span>\n\t\t<\/div>\n\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t
\n\t\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

Samples for Simple Acceptance Decision Rule<\/b><\/p>

The following are sample data from the different areas of calibration.<\/p>

The decision is based on the different rules to show a comparison.<\/p>

2. Mechanical<\/b><\/span><\/span><\/p>

Sample: Torque Wrench<\/b><\/p>

Existing Decision Rule (following APLAC TC 004)<\/b><\/span><\/span><\/p>

Calibration Results<\/b><\/span><\/p>

Clockwise Torque<\/b><\/p>

UUT<\/p>

Indicated Value<\/p>

(N.m)<\/p><\/td>

Max. Permissible<\/p>

Relative Deviation<\/p>

(\u00b1 %)<\/p><\/td>

Mean Measured Value(N.m)<\/td>Error expressed as % of the Indicated Value<\/td>Expanded uncertainty(%)<\/td>

Decision<\/p><\/td><\/tr>

5.00<\/p><\/td>

6<\/td>5.11<\/td>

– 2.20<\/p><\/td>

\u00b10.6<\/p><\/td>

Intolerance<\/p><\/td><\/tr>

15.00<\/td>4<\/td>15.64<\/td>

– 4.27<\/p><\/td>

\u00b10.4<\/p><\/td>

Indeterminate<\/p><\/td><\/tr>

25.00<\/p><\/td>

4<\/td>25.98<\/td>

– 3.92<\/p><\/td>

\u00b10.4<\/p><\/td>

Indeterminate<\/p><\/td><\/tr><\/tbody><\/table>

Specification \/ Tolerance taken from ISO 6789-1 : 2017. Type I , Class B.<\/b><\/p>

The expanded uncertainty is at approximately 95% confidence level with the reported coverage factor, k <\/i>= 2.<\/p>
\u00a0<\/td>

This item fulfils the requirements given in the above stated standard.<\/p><\/td><\/tr>

Final Statement in report<\/p><\/td>

The requirements stated in this report are taken from the above stated standard.<\/p><\/td><\/tr>

\u00a0<\/td>

Measured value marked ** does not fulfil the requirements given in the above stated standard.<\/p><\/td><\/tr><\/tbody><\/table>

New: Simple Acceptance Rule (following ILAC G8)<\/b><\/span><\/span><\/p>

Calibration Results<\/b><\/span><\/p>

Clockwise Torqu<\/b>e<\/b><\/p>

UUT<\/p>

Indicated Value<\/p>

(N.m)<\/p><\/td>

Max. Permissible<\/p>

Relative Deviation<\/p>

(\u00b1 %)<\/p><\/td>

Mean Measured Value(N.m)<\/td>Error expressed as % of the Indicated Value<\/td>Expanded uncertainty(%)<\/td>

Decision<\/p><\/td><\/tr>

5.00<\/p><\/td>

6<\/td>5.11<\/td>

– 2.20<\/p><\/td>

\u00b10.6<\/p><\/td>

Intolerance<\/p><\/td><\/tr>

15.00<\/td>4<\/td>15.64**<\/td>

– 4.27<\/p><\/td>

\u00b10.4<\/p><\/td>

Out of tolerance<\/p><\/td><\/tr>

25.00<\/p><\/td>

4<\/td>25.98<\/td>

– 3.92<\/p><\/td>

\u00b10.4<\/p><\/td>

Intolerance<\/p><\/td><\/tr><\/tbody><\/table>

Specification \/ Tolerance taken from ISO 6789-1 : 2017. Type I , Class B.<\/b><\/p>

The expanded uncertainty is at approximately 95% confidence level with the reported coverage factor, k <\/i>= 2.<\/p>
\u00a0<\/td>

The measured values were observed in tolerance at the points calibrated.<\/p><\/td><\/tr>

Final Statement in report<\/p><\/td>

Measured value marked ** was observed out of tolerance at the points calibrated.<\/p><\/td><\/tr><\/tbody><\/table>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t

\n\t\t\t\t
\n\t\t\t\t\t\t\t
\n\t\t\t\n\t\t\t\t\t\t<\/span>\n\t\t<\/div>\n\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t
\n\t\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

Samples for Simple Acceptance Decision Rule<\/b><\/p>

The following are sample data from the different areas of calibration.<\/p>

The decision is based on the different rules to show a comparison.<\/p>

3. Electrical<\/b><\/span><\/span><\/p>

Sample: Multimeter<\/b><\/p>

Existing Decision Rule (following APLAC TC 004)<\/b><\/span><\/span><\/p>

Calibration Results<\/b><\/span><\/p>

Performance
Test<\/span><\/p><\/td>

Instrument
<\/span>Reading<\/span><\/p><\/td>

Manufacturer’s
Spec<\/span><\/p><\/td>

Expanded Uncertainty(\u00b1)<\/span><\/p><\/td>

Decision<\/span><\/p>

\u00a0<\/span><\/p><\/td><\/tr>

\u00a0<\/td>

Input<\/span><\/p><\/td>

Freq (Hz)<\/span><\/p><\/td>

\u00a0<\/td>

Lower Limit<\/span><\/p><\/td>

Upper Limit<\/span><\/p><\/td>

\u00a0<\/td>\u00a0<\/td><\/tr>

\u00a0<\/p><\/td>

AC Voltage Test<\/span><\/p><\/td>

\u00a0<\/td>\u00a0<\/td>\u00a0<\/td>\u00a0<\/td>\u00a0<\/td><\/tr>
\u00a0<\/td>

6.000 0.0<\/span><\/p><\/td>

45<\/span><\/p><\/td>

6.5 mV<\/span><\/p><\/td>

5.6 mV<\/span><\/p><\/td>

6.4<\/span><\/p><\/td>

0.1<\/span><\/p><\/td>

Indeterminate<\/span><\/p><\/td><\/tr>

\u00a0<\/td>

600.00 0.0<\/span><\/p><\/td>

1 k<\/span><\/p><\/td>

599.9 mV<\/span><\/p><\/td>

587.7 mV<\/span><\/p><\/td>

612.3<\/span><\/p><\/td>

0.1<\/span><\/p><\/td>

Intolerance<\/span><\/p><\/td><\/tr>

\u00a0<\/td>

5.000 0.0<\/span><\/p><\/td>

45<\/span><\/p><\/td>

5.052 V<\/span><\/p><\/td>

4.947<\/span><\/p><\/td>

5.053<\/span><\/p><\/td>

.002<\/span><\/p><\/td>

Indeterm<\/span>inate<\/span><\/p><\/td><\/tr><\/tbody><\/table>
\u00a0<\/td>

This item fulfils the requirements given in the above stated standard.<\/del><\/p><\/td><\/tr>

Final Statement in report<\/p><\/td>

The requirements stated in this report are taken from the above stated standard.<\/p><\/td><\/tr>

\u00a0<\/td>

Measured value marked ** does not fulfil the requirements given in the above stated standard.<\/del><\/p><\/td><\/tr><\/tbody><\/table>

New: Simple Acceptance Rule (following ILAC G8)<\/b><\/span><\/span><\/p>

Calibration Results<\/b><\/span><\/p>

Performance
Test<\/span><\/p><\/td>

Instrument Reading<\/span><\/p><\/td>

Manufacturer’s
Spec<\/span><\/td>		Expanded Uncertainty(\u00b1)<\/span><\/td>

Decision<\/span>\u00a0<\/span><\/p><\/td><\/tr>

\u00a0<\/td>

Input<\/span><\/p><\/td>

Freq (Hz)<\/span><\/p><\/td>

\u00a0<\/td>

Lower Limit<\/span><\/p><\/td>

Upper Limit<\/span><\/p><\/td>

\u00a0<\/td>\u00a0<\/td><\/tr>

\u00a0<\/p><\/td>

AC Voltage Test<\/span><\/p><\/td>

\u00a0<\/td>\u00a0<\/td>\u00a0<\/td>\u00a0<\/td>\u00a0<\/td><\/tr>
\u00a0<\/td>

6.000 0.0<\/span><\/p><\/td>

45<\/span><\/p><\/td>

6.5** mV<\/span><\/p><\/td>

5.6 mV<\/span><\/p><\/td>

6.4<\/span><\/p><\/td>

0.1<\/span><\/p><\/td>

Out of tolerance<\/p><\/td><\/tr>

\u00a0<\/td>

600.00 0.0<\/span><\/p><\/td>

1 k<\/span><\/p><\/td>

599.9 mV<\/span><\/p><\/td>

587.7 mV<\/span><\/p><\/td>

612.3<\/span><\/p><\/td>

0.1<\/span><\/p><\/td>

Intolerance<\/p><\/td><\/tr>

\u00a0<\/td>

5.000 0.0<\/span><\/p><\/td>

45<\/span><\/p><\/td>

5.052 V<\/span><\/p><\/td>

4.947<\/span><\/p><\/td>

5.053<\/span><\/p><\/td>

.002<\/span><\/p><\/td>

Intolerance<\/p><\/td><\/tr><\/tbody><\/table>
\u00a0<\/td>

The measured values were observed in tolerance at the points calibrated.<\/del><\/p><\/td><\/tr>

Final Statement in report<\/p><\/td>

Measured value marked ** was observed out of tolerance at the points calibrated.<\/p><\/td><\/tr><\/tbody><\/table>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t

\n\t\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t
\n\t\t\t\n\t\t\t\t\t\t<\/span>\n\t\t<\/div>\n\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t
\n\t\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

Samples for Simple Acceptance Decision Rule<\/b><\/p>

The following are sample data from the different areas of calibration.<\/p>

The decision is based on the different rules to show a comparison.<\/p>

4. Temperature<\/b><\/span><\/span><\/p>

Sample: Thermohygrograph<\/b><\/p>

Existing Decision Rule (following APLAC TC 004)<\/b><\/span><\/span><\/p>

Calibration Results<\/b><\/span><\/p>

Manufacturer’s Specification : \u00b1 1\u00b0C and \u00b1 5%rh<\/p>

Reference Values<\/p><\/td>

UUT Values<\/td>

Deviation<\/p><\/td>

Decision<\/p><\/td><\/tr>

\u00b0C<\/p><\/td>

%rh<\/td>

\u00b0C<\/p><\/td>

%rh<\/td>\u00b0C<\/td>%rh<\/td>\u00a0<\/td><\/tr>

23.2<\/p><\/td>

55.3<\/td>23<\/td>56<\/td>-0.2<\/td>0.7<\/td>

Indeterminate<\/p><\/td><\/tr>

27.3<\/td>65.4<\/td>28.4<\/td>65<\/td>1.1<\/td>-0.4<\/td>

Indeterminate<\/p><\/td><\/tr><\/tbody><\/table>

\u00a0<\/p>

  1. The calibration results reported indicate all the test results obtained at the time of testing.<\/li>
  2. The expanded uncertainty is \u00b1 1.0\u00b0C and \u00b1 5%rh, at approximately 95% confidence level with coverage factor, k <\/i>= 2.<\/li>
  3. \u00a0<\/li><\/ol>
    \u00a0<\/td>

    This item fulfils the requirements given in the above stated standard.<\/del><\/p><\/td><\/tr>

    Final Statement in report<\/p><\/td>

    The requirements stated in this report are taken from the above stated standard.<\/p><\/td><\/tr>

    \u00a0<\/td>

    Measured value marked ** does not fulfil the requirements given in the above stated standard.<\/del><\/p><\/td><\/tr><\/tbody><\/table>

    New: Simple Acceptance Rule (following ILAC G8)<\/b><\/span><\/span><\/p>

    Calibration Results<\/b><\/span><\/p>

    Manufacturer’s Specification : \u00b1 1\u00b0C and \u00b1 5%rh<\/p>

    Reference Values<\/p><\/td>

    		UUT Values<\/td>

    Deviation<\/p><\/td>

    Decision<\/p><\/td><\/tr>

    \u00b0C<\/p><\/td>

    		%rh<\/td>

    \u00b0C<\/p><\/td>

    		%rh<\/td>\u00b0C<\/td>%rh<\/td>\u00a0<\/td><\/tr>

    23.2<\/p><\/td>

    		55.3<\/td>23<\/td>56<\/td>-0.2<\/td>0.7<\/td>

    Indeterminate<\/p><\/td><\/tr>

    27.3<\/td>65.4<\/td>28.4**<\/td>65<\/td>1.1<\/td>-0.4<\/td>

    Out of tolerance<\/p><\/td><\/tr><\/tbody><\/table>

    \u00a0<\/p>

    1. The calibration results reported indicate all the test results obtained at the time of testing.<\/li>
    2. The expanded uncertainty is \u00b1 1.0\u00b0C and \u00b1 5%rh, at approximately 95% confidence level with coverage factor, k <\/i>= 2.<\/li><\/ol>

      \u00a0<\/p>
      \u00a0<\/td>

      The measured values were observed in tolerance at the points calibrated.<\/del><\/p><\/td><\/tr>

      Final Statement in report<\/p><\/td>

      Measured value marked ** was observed out of tolerance at the points calibrated.<\/p><\/td><\/tr><\/tbody><\/table>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t

      \n\t\t\t\t
      \n\t\t\t\t\t\t\t
      \n\t\t\t
      <\/div>\n\t\t<\/div>\n\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t
      \n\t\t\t\t\t
      \n\t\t\t\t
      \n\t\t\t\t
      \n\t\t\t\t\t\t\t
      \n\t\t\t\t\t\t\t\n\t\t\t\t\t\n\t\t\t\t\t\tLinkedin<\/span>\n\t\t\t\t\t\t<\/path><\/svg>\t\t\t\t\t<\/a>\n\t\t\t\t<\/span>\n\t\t\t\t\t\t\t\n\t\t\t\t\t\n\t\t\t\t\t\tLine<\/span>\n\t\t\t\t\t\t<\/path><\/svg>\t\t\t\t\t<\/a>\n\t\t\t\t<\/span>\n\t\t\t\t\t\t\t\n\t\t\t\t\t\n\t\t\t\t\t\tFacebook<\/span>\n\t\t\t\t\t\t<\/path><\/svg>\t\t\t\t\t<\/a>\n\t\t\t\t<\/span>\n\t\t\t\t\t\t\t\n\t\t\t\t\t\n\t\t\t\t\t\tYoutube<\/span>\n\t\t\t\t\t\t<\/path><\/svg>\t\t\t\t\t<\/a>\n\t\t\t\t<\/span>\n\t\t\t\t\t<\/div>\n\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t
      \n\t\t\t\t\t
      \n\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t","protected":false},"excerpt":{"rendered":"

      Samples for Simple Acceptance Decision Rule\u200b The following are sample data from the different areas of calibration. The decision is based on the different rules to show a comparison. 1. Dimensional Sample: Caliper Existing Decision Rule (following APLAC TC 004) Calibration Results Specification\/ Tolerance taken from JIS B 7507 : 2016. Instrument Error of External […]<\/p>\n","protected":false},"author":5,"featured_media":2651,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[29],"tags":[],"class_list":["post-2441","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-news"],"aioseo_notices":[],"_links":{"self":[{"href":"https:\/\/mdmetrology.com.sg\/th\/wp-json\/wp\/v2\/posts\/2441","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/mdmetrology.com.sg\/th\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/mdmetrology.com.sg\/th\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/mdmetrology.com.sg\/th\/wp-json\/wp\/v2\/users\/5"}],"replies":[{"embeddable":true,"href":"https:\/\/mdmetrology.com.sg\/th\/wp-json\/wp\/v2\/comments?post=2441"}],"version-history":[{"count":143,"href":"https:\/\/mdmetrology.com.sg\/th\/wp-json\/wp\/v2\/posts\/2441\/revisions"}],"predecessor-version":[{"id":2643,"href":"https:\/\/mdmetrology.com.sg\/th\/wp-json\/wp\/v2\/posts\/2441\/revisions\/2643"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/mdmetrology.com.sg\/th\/wp-json\/wp\/v2\/media\/2651"}],"wp:attachment":[{"href":"https:\/\/mdmetrology.com.sg\/th\/wp-json\/wp\/v2\/media?parent=2441"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/mdmetrology.com.sg\/th\/wp-json\/wp\/v2\/categories?post=2441"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/mdmetrology.com.sg\/th\/wp-json\/wp\/v2\/tags?post=2441"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}